Discovering Plumbing Basics is Vital for Bathtub Installation
Discovering Plumbing Basics is Vital for Bathtub Installation
Blog Article
What're your thoughts concerning A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard task. If the old bathtub is readily accessible, the task can relocate quickly; if you have to open up a wall surface to eliminate the old tub and also position the brand-new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will require a helper to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the job as well as fit trying it. Instead of working with a service provider to take over a halfway-completed task, it is far better to think about using one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your restroom if you have currently acquired a new tub and also do not need to transform the arrangement of your previous water pipes.
Your devices and also material list should comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Prior to carrying on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Protect the tap in position with the manufacturer provided backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous type must be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the required placement. The wooden boards are valuable in evenly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the level and changing the feet on the tub up until the spirit level checks out level.
To install faucets, fit all-time low of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the supply of water and also examine all joints and also new pipework for leaks as well as tighten them if needed. Fill up the bathtub as well as additionally check the overflow electrical outlet and the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub ought to wait up until the bath tub has actually been made use of a minimum of when as this will settle it into its final position.
Planning for the Setup
Firstly, the supporting frame provided with the bath needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a stiff seal, creating the water to pass through the wall surface between the bath and the tiling, causing complications with moisture and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture rather very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently offered on the market. It is recommended to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very fascinated with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed our blog entry. Those who enjoyed our blog post if you please make sure you remember to share it. Thanks a lot for your time. Come back soon.
Try Here Report this page